7489 DATASHEET PDF

The SGA is a high performance SiGe HBT. MMIC Amplifier. NOTE: The recommended operating current in the preliminary datasheet was mA. MOSFET are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for MOSFET. Datasheet, In Stock. SN datasheet, SN circuit, SN data sheet: TI – BIT RANDOM- ACCESS READ/WRITE MEMORY,alldatasheet, datasheet, Datasheet search site.

Author: Mikabar Maramar
Country: Sudan
Language: English (Spanish)
Genre: Career
Published (Last): 1 May 2013
Pages: 487
PDF File Size: 6.9 Mb
ePub File Size: 12.12 Mb
ISBN: 160-3-89625-338-3
Downloads: 53524
Price: Free* [*Free Regsitration Required]
Uploader: Vuramar

Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

What should I be looking for in the datasheet? R4 should be ON. Sign up or log in Sign up using Google. I assume that the memory enable should just stay low at all times, but I did try moving it around.

Thanks for cleaning up the schematics. So now I have the following schematics more or less copied from here. Thanks for the answer.

Schematics for using IC memory – Electrical Engineering Stack Exchange

I still can’t get it to work, but I will accept your answer because you provide a general schematics for the chip. As you said, you could just tie ME low with a wire for this test. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

  KAGUYA LUNAR ATLAS PDF

ME high regardless of the! The pdf sheet on this part specifies a load of mA as being a safe maximum load, as a current sink.

Sparky 11k 2 15 Email Required, but never shown. Sign up using Facebook.

(PDF) 7489 Datasheet download

As this is an old original bipolar TTL pert, it may get warm in operation, but if it is HOT you don’t want to touch it for longsomething is wrong. Note that the LED current is limited to less than 2 mA, minimizing excess dissipation in the chip. Thanks for the answer. We Hiif you’re in write mode both controls! WE low by closing the switch – it might be worth pulling this high with a resistor datashert you’re not trying to write, but that might be irrelevant – at the datashest you’ve got two possible control states: Remember, both ME and WE need to be active low in order to write data to the chip.

WE state – and if 7498 high they shouldn’t be able to light the LEDs. To comment, click on the “add a comment” link by the answer or question your commenting to. It is my first time using this. The outputs are inverted OC type.

Most of today’s LEDs have a Vdrop of about 3. This IC can sink 12mA max per output pin.

I have attempted to draw a schematics of my setup for the below. The 7849 are “active low” – if you write a High 1 to a memory location, you will read back a Low 0. I got more and I have finally gotten everything to work.

  DODI 5000.2 PDF

Sign up using Facebook.

LEDs aren’t very fussy about current, as long as it is less than their Absolute Maximum rating. For example, in the answer to the earlier question, the resistors R1, R2, R3, and R4, were suggested to be 2. WE to replace the overscore notatation used for active low in the datasheet – you have! A resistor obeys Ohm’s law, and choosing a resistor value is a matter of the permissible voltage and current, and power voltage drop x current according to application. Yeah I’m new to writing on this, having leeched much info in the past.

Understanding pull-up resistors and the memory chip Ask Question. It may not be able to drive LED’s directly. Why are two LEDs on? If the LEDs drop 2 volts, assume there is 3 volts across the resistors there’s be a bit less, because the can’t pull its outputs quite to groundthen for 20 mA, you’d want Ohms.

7489 Datasheet

Yeah I know It’s irrelevant but what the hell! You could try using a ground strap thin copper braid around your wrist and ground to the IC’s ground to avoid static damage. I have been learning about the memory chip.

ME always low, and hopefully can toggle!

Share