All OMRON products are capitalized in this manual. The word .. purpose and a comparison between the CQM1H and the CQM1. Section 2. 1. V4+. Voltage pin, input 4. 2. V Common pin, input 4. 3. V3+. Voltage pin, input 3. 4. V Common pin, input 3. 5. V2+. Voltage pin, input 2. 6. V Common . View and Download Omron CQM1 operation manual online. Programmable Controllers. CQM1 Controller pdf manual download. Also for: Sysmac cqm1.
|Country:||Republic of Macedonia|
|Published (Last):||23 October 2005|
|PDF File Size:||9.64 Mb|
|ePub File Size:||18.41 Mb|
|Price:||Free* [*Free Regsitration Required]|
For nj-series cpu unit. The heater burnout alarm output will turn OFF if the setting is changed to 0. The memory area used to hold the active program, i. Even if teaching is performed success- fully outside the stable sensing range, the E2C-MA11 in operation may not reset properly.
Page numbers refer to the previous version. Flashes during normal trans- mission. Page Glossary output bit A bit in the IR area that is allocated to hold the status to be sent to an output device. Handling Power On Maximum transmission delay time Tmax: Nomenclature Lit when an internal error, such as IC malfunctioning, occurs.
Omron CQM1 Operation Manual
Words SR to SR cannot be changed. The transmission distance depends on the type of wiring used.
Glossary output bit A bit in the IR area that is allocated to hold the status to be sent to an output device. Read the integral time. Decimal Monitor With Sign 3-word data modification can be used dur- ing execution.
Connector Type Dimensions when Mounted mm Approx.
Forced Zero zero-shift When zero input is turned ON while the Unit is sampling data, the scaled con- version data will be shifted to zero and stored as mnual data in the input word, or the comparison result flags of the input word are turned ON or OFF accord- ing to the comparison result processed by the Unit.
Page Programming and Adjustment 3. If the ERR indicator is still lit, the Vqm1 needs repairs. Page On the other hand, the SCL instruction cannot process negative values. Scaling Example for Measuring Lengths Using a Sensor with an Input of 4 to 20 mA If the output of the sensor is 4 mA when the length of the object sensed by the sensor is 10 centimeters and the output of the sensor is 15 mA when the length of the object is 30 centimeters, the following data should be input.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of OMRON. Glossary nonfatal error A hardware or software error that produces a warning but does not stop the PC from operating. Input the operand address.
Transmission terminals manuql and 2 can be connected in any order.
OMRON CQM1 OPERATION MANUAL Pdf Download.
IOTC — — C: Weight 26 g Note 1. Don’t have an account? Don’t have an account? Are there any loose replace wires.
Axis adjustment or sensitivity adjustment teaching. Ready indicator green, lit when the Unit is rec- Word number indicator orange, lit when two words are ognized as the Temperature Control Unit used and not lit when a single word is used Terminal screws: The forced-zero shift function is not effective when the timing hold is set to peak-to-peak hold.
Note The sensitivity of the E3C-MA11 is set to maximum if teaching is performed with very little light or if the sensor head is not manuaal within the sensing dis- tance. Troubleshooting Flowcharts Section Non-fatal Error Check Although the PC will continue operating during non-fatal errors, the cause of the error should be determined and removed as quickly as possible to ensure proper operation. When zero input is turned ON while the Unit is sampling data, the scaled con- version data will be shifted to zero and stored as binary data in the input word, or the comparison result flags of the input word are turned ON or OFF accord- ing to the comparison result processed by the Unit.
The teaching indicator orange will be lit. WE Revision code The following table outlines the changes made to the manual during each revision. These compo- nents lock together at the sides, allowing simple changes in the size and capac- ity of the PC. Word n Data output Dimensions when Mounted mm Approx. When the input word is set towhich is the scaled conversion data of the smallest object, the teaching for the X1 value has been correctly executed. The status of mqnual and contents of words being monitored can also be controlled.
Move the object to the position where you want to turn ON the output and press the teaching button. Page Cable Connections