DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Kajijin Mazukus
Country: Republic of Macedonia
Language: English (Spanish)
Genre: Career
Published (Last): 14 June 2017
Pages: 70
PDF File Size: 16.2 Mb
ePub File Size: 20.4 Mb
ISBN: 852-3-35308-831-5
Downloads: 47745
Price: Free* [*Free Regsitration Required]
Uploader: Braran

Press any key to continue. Press Cancel to exit the utility. Disconnect the cables from the Entry Sensors. Scan Axis Motor SV. CR Tubes System 24 T Remove the T screw that attaches the left panel to the left cover.

Remove the Touch Control Panel from the holder and leave it carefully hanging as shown in the picture. Product Support on page Page 73 System Error: Unable to determine warranty status.

The Touch Control Panel then prompts you push down Piston 0.

See Tools 2 on page Right Cover on page Remove screw and straight bushing. An error with the Rewinder 2 System Lower Rewinder has been detected. Remove Left Front Trim from the product. Table Of Contents Formatter Remove the front Manhal screw that secures the front left side of the Top Cover to the printer. While pushing the plastic part of the slider center support against the roller Atighten loose screws B. Wait until you see the following message. Make sure that you supply all the information accessed by pressing the Up and Cancel keys together while viewing the system error screen, or preferably provide the product log and diagnostic package to HP.

  ADCCAC RULES PDF

Adjustment scanner Y-Axis scale The scanner may produce a vertical distortion in scanned images. Lift up the blue lever on the left.

HP DESIGNJET T1300 ePrinter series Service Manual

Free the other end of the right metal link of the right Bi-stable Deisgnjet if necessary, play slightly with the Lower Roll Cover. Unroute the Scan-Axis Motor supply cable from the cable clamp. Open the upper roll cover and press OK.

If no paper is loaded, the test will continue.

HP DESIGNJET T EPRINTER SERIES SERVICE MANUAL Pdf Download.

CN Interconnect Cables Kit 44in. An unsupported or reused part has been installed. Remove all the printheads and insert them alone one by one, Closing the latch and the carriage cover after every insertion. The following is a list of all internal service calibrations available in the product. Remove the Scan-Axis Motor from the product. Pull the blue handle upward until the printhead is released from the carriage.

  COBY KYROS 7042 PDF

Installation Switch off the product and remove the power cable. Remove the Scanner Position Sensor from the holder by unclipping it keep the sensor cable plugged into the sensor. Table Of Contents Single-sheet Sensor Emergency firmware upgrade w If the above steps do not work, try using a different type of print queue.

Primer motor In the Diagnostics menu, scroll to Service Station and press on this menu option. Disconnect cable and hooks. If you have not fed enough paper into the product, the diagnostic will show a message saying that the paper was not detected and the test will sergice and the product will reboot.

When you reinstall the full bleed foams, take care to correctly seat them to servjce possible damage to the Carriage Assembly Hard Disk Drive Removal and installation Remove the Left Ink Cartridge Door. If the issue is new and the issue happens since the first boot, do not replace the HDD. Set the Pinchwheel Alignment Tool on the print platen.

Do not unscrew the hexagonal nut from bumper assembly. Disconnect the 6 Power and Data connectors around the Interconnect Board.

Share